CAD screenshots for the Mk1.
As the first iteration, we were primarily interested in just creating an assembly that would test certain concepts we wanted to apply, while assessing how the final product would interface with the user.
The design consists of only two parts; a housing and a card tray. A business card would be loaded into the card tray, which is then inserted into the housing with a rubber band connecting the two. A pair of retention flexures would retain the card tray in the retracted position. As the flexures are depressed, the teeth on them would disengage from the notch on the card tray, allowing it extend out due to the rubber band, until the retention flexures re-lock the card tray at the extended position notches
Printed parts of the Mk1.
The housing was printed with ABS on the Stratasys Dimension Elite, while the card tray was printed with PLA on a Makerbot Replicator.
The overall design was pretty impractical, as it was really bulky and only accommodated for one business card.
Hook on the front of the housing to mount the rubber band. It was determined that this way of attaching the rubber band between the housing and the card tray was a bit of a hassle, and resulted in inconsistent actuation.
Retention flexure seen inside housing. In hindsight, we realized the flexures were pretty inaccessible through the string routing hole we designed in, and was only actuatable by drilling an additional hole at the top of the housing.
Concept sketches for Mk2.
The objective for the 2nd iteration was to optimize the dispensing mechanism and the card carrying capacity. We decided to go with leaf spring tray that can hold up to 5 cards, which applies an upwards pressure on the cards while they are loaded in the housing. A slider equipped with a small rubber coated spring would grab the card with friction while dispensing it and bend away from the card stack on it’s way back. We chose this method because we determined it would be the most compact and reliable dispensing mechanism while causing the least amount of potential damage to the cards.
CAD assembly of Mk2.
CAD assembly exploded view of Mk2.
CAD side sectional view of Mk2.
Here you can clearly see how the tray spring and slider spring interacts within the housing.
CAD rear view of Mk2.
The grooves of the slider rides on the rails designed into the housing.
Mk2. parts printed out of ABS on the Stratasys Dimension Elite
Mk2. Housing.
Here you can see the slot where the business cards dispense from. The notch in the front is the fixed of where the rubber band will mount to.
Mk2. Slider.
The spring can be seen with plasti-dip already applied onto it. The notch in the rear is where the moving end of the rubber band will mount to in order to actuate the slider.
Mk2. Card Tray. The back wall of the card tray has small nubs on the top and bottom, witch lock into grooves designed into the housing. The portion at the far rear of the card tray is a handle allowing the user to easily grab and remove it in order to reload more card.
Mk2. Housing and Slider assembled together. The Slider fit perfectly onto the rails and slides around effortlessly without any work don onto it. We designed in a 0.020" spacing between all sides to achieve this fit.
Full assembly of Mk2. with business cards and rubber band.
Mk2. Test Fire Video. While the mechanism worked, we didn’t quite get the business card to extend as far out as we wanted to.
Concept Sketches for Mk3. For the 3rd and final iteration, our focus was making improvements over the aspect we liked about from the Mk2., while integrating the watch band and slider locking mechanism as well. In order to get the card to deploy out further, we designed the card tray with a double leaf spring design to support both the front and rear of the business card. For the slider lock, we decided to use a pair of retention flexures as we did in Mk1., but were able to orient them in a much more optimal location.
CAD assembly of Mk3.
CAD assembly exploded view of Mk3.
CAD side sectional of Mk3. You can see the double leaf springs on the card tray, as well as the slider lock flexures in front of the slider.
CAD bottom sectional of Mk3. This view shows a better representation of how the slider lock flexures are designed. The holes on the sides allow for a string to be routed through, and tied around the flexures to actuate them.
Mk3. parts printed out of ABS on the Stratasys Dimension Elite
Mk3. Housing Front View. The holes on the sides are there to guide the trigger sting towards the user’s fingers.
Mk3. Housing Side View. The hole on the side is where the trigger string will route out of after it has been tied off to the locking flexures inside. The two little nubs at the bottom are where the watch band will be mounted to.
Mk3. Housing Rear View. Very little change has been made in terms of how the housing and slider will interface with one another, as the results from Mk2. were great in that respect.
Mk3. Slider Front View
Mk3. Slider Side View. The only change made to this part from Mk2. was that a little more material was added to the front of the slider, in order to increase the contact area between the slider and the locking flexures in the housing.
Mk3. Slider Rear View.
Applying Plasti-Dip to the leaf spring on the slider. This was the most painful process of the assembly, as we tried to get a nice smooth layer on the spring without it getting on any other part of the slider.
The Slider after the second coat of of Plasti-Dip has been dried. A little messy, but we were able to get a nice, smooth surface where the spring would engage the business card.
Cleaing off excess Plasti-Dip and trimming it off the side walls of the spring so it doen’t interfere in while sliding around in the housing.
Mk3. Card Tray Front View
Mk3. Card Tray Side View
Mk3. Housing assembled with the 3D printed watch band. The watch band was printed out of PLA on the Makerbot Replicator in two pieces.
The watch band is connected with a couple of M2 socket head cap screws, which thread into the housing, but just act as loose fitting pin in the watch band to allow it to swivel around.
Rubber band attached, and the Slider in its deployed position.
The slider in the retracted/loaded position. As seen in this picture, the Slider is held in its position as the locking flexures prevent it from going forward until the string is pulled.
Actuation string routing.
The complete Mk3. assembly mounted on the arm.
In order to actuate the string, the user grabs onto the small bar with their middle and ring finger as shown above, and simply cocks their wrist backwards. Now you can see why we decided to call this the Corporate Spiderman. :D
[WARNING: Loud tools operating in background]
Initial test videos of the final product which shows that the device can be operated repeatedly with multiple cards inside of it. We were also able to consistently get our business cards to extend out further compared to the Mk2., showing that the double leaf spring was indeed the effective.
Testing while underneath a sleeve. The Mk3. is compact enough to fit under the sleeves of a regular fit long sleeve shirt.
Single person operation test.
Comparing all the iterations side by side. Through this project and design, we were able to demonstrate the rapid prototyping and iterative design capabilities of 3D printers.
The Mk3. is fully functional, as opposed to Mk1., and has made significant improvements in terms of size, weight, functionality, and even aesthetics.
Corporate Spiderman
[TL;DR – Scroll to bottom for videos of it in action!]
The Corporate Spiderman is a wrist-mounted business card dispenser, with stealth and style at mind. The professional world is tough with ever-increasing competition, making it hard for young job-seekers from standing out in the crowd. With the Corporate Spiderman, you too can become a networking and job-hunting superhero. Make your business card appear out of thin air, and present it in style! Recruiters will be awed, your peers will be impressed, and you will be the envy of all those still in the recruiting grind!
Now with the terrible infomercial-esque intro out of the way… The Corporate Spider was a project that a couple friends and I worked on as our class project for the Rapid Prototyping (MAE183C) class at UCLA. The objective of the project was to design and manufacture a product that capitalizes on the benefits of Solid Freeform Fabrication techniques (commonly referred as “3D Printing”). Some advantages of this technique includes its capability to create complex geometries, internal features, and functional assemblies, as well as how it enables iterative design through rapid prototyping.
With a class-wide limitation of 8-hours of printing time for each of the 3 print cycles we were given, we realized that our design could not be overly complex or large. With these limitations, our group decided to something that would innovate further on existing products, be practical enough to be actually used, while integrating our playful nature into the design.
All our parts would be produced out of ABS through Fused Deposition Modeling (FDM) on the Stratasys Dimension Elite, while other non-critical parts would be made out of PLA on a Makerbot Replicator.
Role |
Mechanical Designer |
For |
MAE183C: Rapid Prototyping |
Date |
3/17/2018 |
Type |
School Project |
Collaborators |
Derrick Benson & Samuel Chen |